Buy a Replacement Control Board for Your Electric Range
It's inevitable that with frequent use, your electric range's control board may one day fail to keep up with your demand for hot meals day after day. The control board regulates the oven's temperature, interacts with its power source, and keeps the entire appliance running. Replacing a defective control board with a new one may seem intimidating to most people, but with our help, it will be quicker and easier than you ever imagined.
Overview of the Process
The process doesn't require any prior experience to complete, and with a few careful steps and a bit of troubleshooting, you can have your electric range back up and running as it should be. To simplify the process, we have broken it down into several steps that we will go over here.
Step 1: Disconnect Your Electric Range
Safety should always be the top priority when tinkering with electrical appliances. Make sure to disconnect the electric range from its power source to avoid any potential damage to the appliance. If your range has a hardwired electrical connection, switch the breaker to the circuit off.
Step 2: Identify the Control Board Location
The control board location varies from one appliance to the next. It is usually found towards the lower back of the stove, sometimes placed behind the controls or behind the range. Once you have located the control board, you can go ahead and remove it from its bracket using a screwdriver.
Step 3: Install Your New Control Board
Turn off the breaker on the circuit before you begin. Place the new board onto the mounting bracket, then use the screws provided to connect it. Make sure to install the new board exactly as your old one had been. Once you have done that, you can reconnect the electric range to its power source.
Step 4: Check Electrical Connections
Verify that all connections are firm and secure. Make sure none of the cables have become loose or disconnected. At this stage, you can also check its compatibility with the range's wiring.
Step 5: Restore the Electric Range's Power
Finally, restore the electric range's power source by switching the breaker back on. If you are using a plug, plugging it in should do the trick. Many modern models come with a diagnostic system that indicates whether everything is working properly.
Obtaining a New Control Board
Depending on your particular electric range's make and model, you may need a replacement control board that fits accurately and correctly. That's where a reliable appliance repair technician can be helpful. Many technicians have access to a wide range of appliance parts and can serve as an excellent source for obtaining the corresponding control board piece for your electric range.
In addition, having a qualified technician to help inspect, diagnose, and replace your control board is highly recommended. Their expertise and experience in the field can help you make sound decisions regarding the operation and maintenance of your electric range.
Call a Local Reliable Appliance Repair Technician
If you wish to read more information about electric range control board, please click here. Make sure to contact a reliable appliance repair specialist in your area. Doing so ensures that you have access to the best possible service and advice. For reliable and quick service in San Diego, call Local Reliable Appliance Repair at tel:(866) 516-1222.
Electric Range Control Board Tips and Best Practices
- Conduct Regular Cleaning and Maintenance – Cleaning and maintaining the control board of an electric range can help extend its lifespan and reduce the likelihood of issues arising with it. Cleaning the area around the control board, keeping all surrounding areas tidy, and avoiding contact with liquids also helps to prevent any accidental damage to the board.
- Check Electrical Connections – It is important to regularly check the electrical connections of the electric range for any wear and tear. This includes disconnecting power and visually inspecting the control board’s wiring for any loose connections. Proactively checking for these warnings signs can help reduce the chance of a breakdown happening or help identify the issue before any further damage is caused.
- Test for Short Circuits – If an electric range is failing to operate correctly or displaying errors, it may be a sign of a short circuit. Checking for shorts regularly helps to reduce the risk of having a full blown electrical breakdown. Testing for any shorts should be done before inspecting other areas, such as the oven’s switches and motor.
- Verify Thermostat Settings – The thermostat on an electric range is responsible for regulating the stove’s temperature. Checking the settings to ensure they are correct and properly adjusted can help reduce the chance of the control board malfunctioning.
- Consult with a Technician – If any issues still arise with the electric range’s control board after following these steps, it is important to consult with a local HVAC or appliance technician. They can provide specialized expertise and advice on what to do and help identify any underlying issue that may be at play.
- Replace Parts When Necessary – If a technician concludes a part needs to be replaced, it is best to act on that recommendation and replace it promptly. This helps avoid the risk of a major breakdown happening and prolongs the lifespan of the electric range.
Average Repair Cost for Electric Range Control Board in San Diego
Having issues with your electric range control board? Get the best advice by calling Local Reliable Appliance Repair at 866-516-1222.
The cost of an electric range control board repair in San Diego depends highly on the parts and labor required. As a general guide, minimum repair cost (including parts and labor) may range from $150-$200, and complex repairs/ installations may cost anywhere between $300-$400. A detailed list of the most commonly replaced parts is given below.
- Temperature sensor/ probe: This is responsible detecting the temperature of the oven, and may cost somewhere between $10-$20.
- Control board: A new control board can be between $150-$200.
- Selector knob: Used to control cycle and temperature mode, this part costs around $15-$25.
- Thermostat: Thermostats are important for temperature control and cost between $25-$50.
Additionally, all repairs/installations require certain tools and materials such as wrenches, screws, replacement parts etc. These will be estimated and charged separately depending on the complexity of the project.
To get the most accurate estimates, get in touch with Local Reliable Appliance Repair at 866-516-1222. They provide prompt and reliable repairs/installations in the city of San Diego.
Electric Range Control Board: What You Need to Know
An electric range control board is a crucial part of your cooking appliance and requires proper expertise to properly maintain and repair. If you're having problems with your electric range control board, you'll want to call a professional HVAC and appliance repair technician who knows what they're doing.
The Benefits of Reliable HVAC and Appliance Repair
Reliable is a family-owned HVAC and appliance repair company located in San Diego, CA. The company offers same-day service for appliance and HVAC repair and installations, and their technicians have a minimum of five years of experience in the field. They specialize in electric range control board repairs, and offer fair and affordable pricing. Plus, as a first-time customer, you can take advantage of the $25 off labor promotion.
Why Should You Consider Reliable HVAC and Appliance Repair?
Reliable HVAC and Appliance Repair stands out among the competition because it is a licensed, insured, and fully certified local San Diego company. Its technicians are highly trained and experienced. Plus, they offer same-day service, making sure that your repairs are done quickly and correctly. To take advantage of their services, contact them at (866) 516-1222.
If you're having issues with your electric range control board, there is no need to worry – just call the professionals at Reliable HVAC and Appliance Repair. This local San Diego family-run business has licensed and insured technicians with a minimum of five years of experience. Specializing in electric range control board repairs, the company offers same-day service, making sure that your appliance is up and running in no time. Plus, as a first-time customer, you can take advantage of the $25 off labor promotion. Contact them today to schedule an appointment at (866) 516-1222.
FAQ – Buy a Replacement Control Board for Your Electric Range and Electric Range Control Board
What is an electric range control board?
An electric range control board is the main control for an electric range's functions. It manages the stovetop burners and oven, providing power to the components and allowing you to adjust the temperature and various settings.
Where can I buy a replacement control board?
Replacement control boards can be purchased from many home improvement stores and online retailers. Prices vary depending on the type of control board and the brand of stove.
Is the installation of a new control board difficult?
Installation of a new control board typically requires basic mechanical knowledge and tools. Most manufacturers provide detailed instructions on how to perform the installation correctly and safely.
Do I need specialized tools to replace the control board?
It is generally not necessary to use specialized tools for the installation of a new control board. Standard hand tools and a screwdriver are usually sufficient.
What should I do if I have difficulty replacing the control board?
If you have difficulty replacing the control board, it is best to call a professional for help. Local Reliable Appliance Repair at tel:(866) 516-1222 can provide assistance with replacing the control board and any related services.