Reliable HVAC & Appliance Repair (866) 516-1222

Licensed HVAC & Appliance repair expert service

How to Fix GE Gas Stove Burner that wont Light

How to Fix GE Gas Stove Burner that won’t Light

How to Fix GE Gas Stove Burner that won't Light

Gas stove burner getting no spark during the ignition? Also the GE Gas Stove Burner won't light? Taking extra time to heat things? Don't panic. Here are few steps to fix the GE Gas Stove Burner issue.

Issues with the Spark Generator

The spark generator is a device that is responsible for creating an electric spark during the ignition. Therefore, if it is not functioning properly, you will face problems with GE gas stove burner. To check if the spark generator is the one causing the issue, follow the steps below.

  1. Try a different burner. If the other burner works and the other one does not, then it's a sure indication that the spark generator is malfunctioning.
  2. Try pressing the igniter several times. This will discharge the electricity from the spark generator, helping it to reset.
  3. Give it a minute or two and try igniting the burner again. This may do the trick.
  4. If the issue remains, it's possible that the spark generator is defective. You should consult a professional or take a look at an online tutorial to replace the spark generator.

Issues with the Igniter Electrode

Another possible cause that could be preventing your GE gas stove burner from lighting is an issue with the igniter electrode. Follow the steps below to troubleshoot this problem.

  1. Test the gap between the igniter and the gas valve. It should be between 1/4-1/2 inch for proper functioning.
  2. Check for build-up that may have blocked the gas flow. You can use an electrical cleaner to remove the debris.
  3. Adjust the igniter to the right tension and testing. Lift the igniter away from the valve and push it back again with slight pressure.
  4. Make sure the igniter has good contact with the gas valve. If the contact points are weak, your GE gas stove burner won't light.

Issues with Pilot Light

Finally, the pilot light of your gas stove might be the issue. Follow the steps below to fix it.

  1. Locate the pilot light and make sure it is in the "on"position.
  2. Open the gas valve by pushing and turning the appropriate knob.
  3. Push the igniter and wait for a few seconds. The pilot light should light up.
  4. Keep the knob in the "on" position for a few seconds. This will ignite the pilot light. Once it is on, you can turn the knob back to the "off"position.

These are just a few steps that you can take to resolve the issue with the GE gas stove burner. However, it is best advised to seek professional assistance if the problem persists. The experts at Local Reliable Appliance Repair can diagnose and fix the issue within minutes. Give them a call at (866) 516-1222 to book an appointment with them.

If you wish to read more information about GE Gas Stove Burner won't light, click here.

How to Fix GE Gas Stove Burner that won't Light
How to Fix GE Gas Stove Burner that won't Light
How to Fix GE Gas Stove Burner that won't Light

GE Gas Stove Burner Won't Light: Manufacturer and Technician Recommendations

It is important to take proactive measures when your GE gas stove burner won't light. To ensure top quality safety and quality of your gas stove, the following are recommended manufacturer and local appliance technician recommendations to avoid GE gas stove burner won't light issues.

  1. Inspect the power source. Make sure that the power cord is safely plugged in, and that you are using the designated fuse box (if required).

  2. Verify the burner cap is properly seated and the mounting hardware is properly tightened.

  3. Check the electrodes for visible signs of damage and ensure the wiring connections are properly secured.

  4. Clean the burner cap and electrodes with a soft cloth and mild soap solution. This will help remove debris, dirt, and dust that can affect the performance of the burner.

  5. Check the gas supply line for any blockages or leaks.

  6. Ensure the igniter and thermocouple are in good working order and connected properly.

  7. Schedule routine maintenance on your gas stove with a reliable appliance repair service in the San Diego area. This is the most efficient way to ensure top performance of your gas stove.

  8. If issues continue to occur, contact a licensed gas technician for further diagnosis.

Following these recommendations can help you avoid any GE gas stove burner won't light issues. If you ever find yourself in need of assistance with your gas stove, you can always contact a local appliance repair service such as Local Reliable Appliance Repair.

Average Repair Cost for GE Gas Stove Burner Won't Light

If your GE gas stove burner won't light, don't worry: Local Reliable Appliance Repair provides professional advice on repair cost in the city of San Diego.

In San Diego, repair costs can range from the minimum for simple repairs to a higher amount for complex ones. The most common replacement parts typically include the igniter, wire harness, and connector, with their respective costs depending on the specific part and its rarity.

Labor costs for this repair will depend on the technician's experience and skill. You should also factor in the cost of materials, such as those required for installing insulation or special tools.

To get an accurate price estimate, call Local Reliable Appliance Repair at (866) 516-1222 for a detailed itemized list of parts and their prices in San Diego.

Diagnosing a GE Gas Stove Burner That Won't Light

Are you having issues with your GE gas stove burner not lighting? Don't worry! Fortunately, you can often diagnose and repair this issue yourself and avoid the need for professional service. Here are some steps you can take to identify the issue and repair your GE gas stove.

First, check if the burner is properly adjusted, as this can be an easy fix. Make sure the burner is placed correctly on the burner base and the burner holes are lined up with the igniter.

Next, examine your igniter. Make sure the igniter electrode gap is not too wide. This can be done with a ruler or tape measure and should be 0.24 inches. If the gap is too large, adjustment is needed.

Your igniter should produce a spark when the burner is turned on. Visually inspect the gap to make sure there is a spark generation. If there is no spark, you might need to clean it. Take a needle and gently remove any dirt from the gaps.

Check the gas valve to make sure it’s fully open. You can easily determine if the valve is open or closed by turning the knob once. If you hear the sound of a spark, you’ll know the valve is open and not need to be adjusted.

Finally, if none of these steps rectify your issue, it might be time to contact a professional. Reliable Appliance Repair, a local family-owned business in San Diego, provides excellent repair services for any of your HVAC and appliance needs. Their highly trained technicians are licensed, insured and have at least 5 years of experience in the field. As a first-time customer, you can get $25 off labor. Need same-day service? Reliable Appliance Repair offers same-day HVAC and appliance repair and installation services, so you can rest assured that your problem will be solved in no time. Contact (866) 516-1222 today!

FAQ: How to Fix GE Gas Stove Burner that won't Light and GE Gas Stove Burner won't light

What should I check first if a GE gas stove burner won't light?

First, check the gas supply. Make sure the gas valve is open, and check for any kinks or damages in the supply line. If the gas supply is okay, next, inspect the igniter electrode for corrosion or physical damage.

What are some common issues that should be checked if a GE gas stove burner won't light?

Common issues to check are the burner knob and the spark module. Turn the knob to the 'on' position, then check to make sure the spark module is functioning properly, as it's responsible for lighting the burner. Additionally, strongly consider cleaning the vents and burners of the appliance.

How can I test the igniter electrode if the GE gas stove burner won't light?

Using a multimeter, test the continuity of the igniter electrode. If the electrode is broken or there’s no connection, the burner won’t work. To test the continuity, set the multimeter to the 'RX1' setting and place the probes on the igniter electrode body and the electrode ground.

If the issue remains unsolved, what should I do?

If the issue remains unsolved, please call a reliable and local appliance repair service for further assistance. We highly recommend Local Reliable Appliance Repair.